>>> KIT AVAILABLE <<< All In One v3.1 PCB 56i Kit for sale !

Discussions related to MegaDrum Hardware

Re: >>> KIT AVAILABLE <<< All In One v3.1 PCB 56i Kit for sale !

Postby OrkUn® » Mon Oct 19, 2009 7:49 pm

Thank you synthex I'll load programs thank you 2 much!! ;)
OrkUn®
 
Posts: 14
Joined: Sun Oct 11, 2009 8:29 pm

Re: >>> KIT AVAILABLE <<< All In One v3.1 PCB 56i Kit to sell !

Postby kokoyo » Sat Oct 24, 2009 3:08 pm

Synthex wrote:To help assembling, here are some pictures and tips :


---------------------------------------------------------

BEFORE START PLEASE WATCH THIS VIDEO :
http://youtube.com/watch?v=I_NU2ruzyc4&feature=related

---------------------------------------------------------

PCB_v31_Finish.jpg

---------------------------------------------------------

USB ON :

USB_ON_2.jpg


USB_ON.jpg

---------------------------------------------------------

Components must be located on the side of the top white silk screening.
You just need soldering on the bottom side.
Holes on the pcb are copper coated to connect both sides of the board.

---------------------------------------------------------

Identification of components :

yellow violet black gold = 47 ohms
brown black brown gold = 100 ohms
red red brown gold = 220 ohms
yellow violet brown gold = 470 ohms
brown black red gold = 1 Kohms
brown green black brown brown = 1.5 Kohms
yellow violet red gold = 4.7 Kohms
blue red red red = 6.2 Kohms
brown black orange gold = 10 Kohms
yellow violet orange gold = 47 Kohms

15 = 15 pF
22 = 22 pF
1n = 1 nF
104 = 100 nF
470nK = 470 nF

12.000 = 12 MHz
20.000 = 20 MHz

---------------------------------------------------------

On the PCB, the square pad is always the pin number 1.

---------------------------------------------------------

Do not solder ICs (U1, U2, U3, U5 to U11) on the PCB.
You must use sockets.

---------------------------------------------------------

1N4148, 4N4007, 47 uF, 100 uF and all ICs (U1 to U11)
are polarized and MUST be inserted in only ONE direction.

---------------------------------------------------------

The green component, with a SILVER ring, is the inductor (L1).

---------------------------------------------------------

For the "R lcd" you can use the 47 ohms resistor (the big blue resistor).

---------------------------------------------------------

To test, you can use a jumper on the "Power Selection" connector :

PowerJumper.jpg

---------------------------------------------------------

HH_Jumpers.jpg


Jumper A : High Input Impedance
Jumper B : Low Input Impedance
Jumper C : Tip = +5Volts ; Ring = Input
Jumper D : Ring = +5Volts ; Tip = Input

---------------------------------------------------------


Thank you synthex, I really want to have one, Do you have some test infors about latency: this board--> PC???
kokoyo
 
Posts: 2
Joined: Sun Oct 18, 2009 4:39 pm

Re: >>> KIT AVAILABLE <<< All In One v3.1 PCB 56i Kit to sell !

Postby Synthex » Sat Oct 24, 2009 3:14 pm

kokoyo wrote:Thank you synthex, I really want to have one, Do you have some test infors about latency: this board--> PC???

It is possible to achieve under 5ms latency with a good sound card and proper ASIO drivers.

And remember, it takes 3ms for sound to travel 1m in the air. ;)
Synthex
 
Posts: 1471
Joined: Fri Oct 12, 2007 6:06 am
Location: France

Re: >>> KIT AVAILABLE <<< All In One v3.1 PCB 56i Kit for sale !

Postby OrkUn® » Wed Oct 28, 2009 1:44 am

Hey synthex Can we add stereo(L-R) outputs in 644's schematics and can we load drum sound package? like jazz kit?
OrkUn®
 
Posts: 14
Joined: Sun Oct 11, 2009 8:29 pm

Re: >>> KIT AVAILABLE <<< All In One v3.1 PCB 56i Kit for sale !

Postby OrkUn® » Mon Nov 02, 2009 9:44 pm

Hey Synthex U5-U6-U7-U8 vdd pins are connected vcc but U9-U10-U11 16 just connected with itselfs. Shouldn't be all of these connected?
OrkUn®
 
Posts: 14
Joined: Sun Oct 11, 2009 8:29 pm

Re: >>> KIT AVAILABLE <<< All In One v3.1 PCB 56i Kit for sale !

Postby Red » Tue Nov 03, 2009 9:34 am

Just ordered and paid for this full kit and the extra boards.

Can't wait! :D 8-)
Red
 
Posts: 14
Joined: Sun Nov 01, 2009 5:46 pm

Re: >>> KIT AVAILABLE <<< All In One v3.1 PCB 56i Kit for sale !

Postby Synthex » Tue Nov 03, 2009 1:59 pm

OrkUn® wrote:Hey Synthex U5-U6-U7-U8 vdd pins are connected vcc but U9-U10-U11 16 just connected with itselfs. Shouldn't be all of these connected?

Of course, U9 U10 U11 Vdd pin are connected to Vcc.
I will update schematics.
Synthex
 
Posts: 1471
Joined: Fri Oct 12, 2007 6:06 am
Location: France

Re: >>> KIT AVAILABLE <<< All In One v3.1 PCB 56i Kit for sale !

Postby Synthex » Tue Nov 03, 2009 2:35 pm

Red wrote:Just ordered and paid for this full kit and the extra boards.

Can't wait! :D 8-)

Your order has already been sent. ;)
Synthex
 
Posts: 1471
Joined: Fri Oct 12, 2007 6:06 am
Location: France

Re: >>> KIT AVAILABLE <<< All In One v3.1 PCB 56i Kit for sale !

Postby Ruslan-maniak » Tue Nov 03, 2009 6:24 pm

Здраствуйте все русскоязычные. Где и как я могу заказать данный набор Synthex v3.1 PCB56i. А то с английским у меня не очень. :ugeek: Подскажите пожалуйста.
Ruslan-maniak
 
Posts: 2
Joined: Tue Nov 03, 2009 4:31 pm

Re: >>> KIT AVAILABLE <<< All In One v3.1 PCB 56i Kit to sell !

Postby kokoyo » Sat Nov 07, 2009 6:04 am

Synthex wrote:
kokoyo wrote:Thank you synthex, I really want to have one, Do you have some test infors about latency: this board--> PC???

It is possible to achieve under 5ms latency with a good sound card and proper ASIO drivers.

And remember, it takes 3ms for sound to travel 1m in the air. ;)


:o Ordered, :? paid . 8-) me and these things http://picasaweb.google.com/hoatre2001/Relax#5401232175506587618 has been waiting for the fullKIT, InputKIT.
8-) 8-)
kokoyo
 
Posts: 2
Joined: Sun Oct 18, 2009 4:39 pm

PreviousNext

Return to MegaDrum Hardware

Who is online

Users browsing this forum: No registered users and 172 guests

cron